ENG-FUCHS Ceplattyn Kg 10 and similar items

ENG-FUCHS LUBRITECH CEPLATTYN KG 10 LC | DEALER Highly Viscous Adhesive Lubricant | PROFESSIONAL USE ONLY MADE IN GERMANY AND USA THE ENG GROUP LLC (GENERAL OILS) IS THE FUCHS DEALER DISTRIBUTOR | FLORIDA, USA WE DISTRIBUTE THE ENTIRE LINE OF CEPLATTYN LUBRICANTS Lubrication, Maintenance, Service for Open Gears N| D0001790 THIS LISTING: CODE 65101801040, 1 DRUM, 190KG CEPLATTYN KG 10 LC - 374 LB DRUM W/O LINER Hazard Classification Not classified as hazardous under 29CFR 1910.1200 (HazCom 2012). Hazardous Component(s): Chemical name CAS-No. Concentration Graphite 7782-42-5 10 - 20% Polyisobutylene Confidential 5 - 10% Specific chemical identities and/or exact percentages have been withheld as trade secrets. Description CEPLATTYN KG 10 LC is based on carefully selected, high-viscosity mineral and synthetic oils and contains an aluminium-complex-soap as thickener. Especially harmless, chlorine and heavy metal-free additives together with the finest and purest colloidal graphite offer extraordinarily high performance. CEPLATTYN KG 10 LC does not contain solvents. CEPLATTYN KG 10 LC together with CEPLATTYN RN and CEPLATTYN 300 represent the FUCHS LUBRITECH multi phase system. Application The high base-oil viscosity and thus good damping characteristics of CEPLATTYN KG 10 LC makes it suit- able for heavy shock load applications. The solid lu- bricants guarantee temperature-stability of the lube film above the normal temperature range. CEPLATTYN KG 10 LC is according to FALK specification for intermittend application. CEPLATTYN KG 10 LC can be applied via common lubricant spray systems. At temperatures below +5C/+40F additional heating system may have to be used for spraying. As CEPLATTYN KG 10 LC is highly economical for the lubrication of large open gears, consumption can be significantly reduced. Open Gear Drives do the heaviest work in many branches of industry Open Gear drives are very common in the raw materials industry. The girth gear drives that are used in tube mills, coolers, washing drums, kilns, calciners and other machines have to transmit enormous torques? i.e. often up to 50,000 Nm. It is only natural that this kind of force subjects the gear wheels to very high stresses. Such gears are usually designed as spur or helical gears with modified involute profiles. The materials used for the gearing are usually CrNiMo tempered steel (pinion) and alloyed CrMo steel casting or cast iron (girth gear). The lubricant plays an important role The purpose of all design and tribotechnical efforts is to ensure, in spite of the enormous stresses, long-term, trouble-free operation. The primary cause of damaged gear wheels is not exclusively the problem of faulty adjustment of the drives and radial and axial run-out, but also the use of unsuitable lubricants, shortage of lubricant and its incorrect application. Therefore an optimum load-carrying capacity and smoothed gear teeth are to be achieved. An extremely precise alignment of the gears combined with the correct running-in procedures is essential. For the lubrication of Open Gears adhesive sprayable lubricants are most suitable. The best solution has a name: CEPLATTYN Wherever lubrication is required on highly stressed or pre-damaged gear drives, under arctic conditions or in hightemperature environments, FUCHS LUBRITECH can offer the right lubricant from the CEPLATTYN product range. CEPLATTYN adhesive lubricants are recommended by all leading manufacturers of gears and machines. Advantages ? Temperature range: +5 ºC / +120 ºC (+40 ºF / +280 ºF) ? Excellent protection against wear ? Good lube film stability at minimal consumption ? Excellent adhesion ? Good EP-properties ? Reduces tribocorrosion ? Water resistant NOTE TO CUSTOMER: If you purchase 10 of these 190 KG DRUMS, we will not charge you any freight. 4 DRUMS PER PALLET. 3 PALLETS OR MORE AND FREE USA SHIPPING. PROPERTY VALUES UNITS METHOD Reference OGPF00K+5 DIN 51502 Color black Temperature range +5 / +120 ºC DIN 51825 Temperature range +40 / +280 F Base oil min Thickener AI-X Solid lubricants C Base oil viscosity (40 ºC) 10.000 mm2/s DIN 51562-1 Base oil viscosity (100 F) 61.000 SUS DIN 51562-1 Base oil viscosity (210 F) 850 SUS DIN 51562-1 NLGI-grade 0/00 DIN 51818 Dropping point 190 ºC DIN ISO 2176 Dropping point 375 F DIN ISO 2176 Four Ball Test welding load 6500/7000 N DIN 51350-4 Four Ball Test welding load 620 kgf ASTM D 2596 TIMKEN OK-load 50 lbs ASTM D 2509 FZG A/2,76/50 ? damage load step 12 DIN 51354 [LLS] Specific wear 0,2 mg/kWh DIN 51354