Duplicating procedures:
Check below list at the bottom for detailed compatibility (BFT, Beninca, Liftmaster, Chamberlain, Sears Craftsman, Lockmaster, Viking, Powermaster, Haudini, Viper, Cylcone, NSEE, Linear, Multicode, GTO, Mighty Mule and many more)
Compatible with overhead operators and garage doors
Manual included
1. Press & hold button 1 of the duplicator, meanwhile press 4 times the 2 button.
2. Release both buttons. Now the RED LED emits a short flash every 2 seconds.
3. Place the original remote control next to duplicator around 5cm
4. Keep pressing the button of the original remote control and wait for a change flash (as a faster flash) of duplicator RED LED and a change of its color (BLUE) that confirms the correct learning of code. This step may take a few seconds and during that the color LED is WHITE.
5. While the BLUE LED is flashing, press the button of the duplicator where you want to program the code just learnt, and retain pressed until the LED switches off and an extended sound “BEEP” for a reconfirmation of the correct code learning.
This step may take some seconds.
6. The copy has been happened with success. Repeat the duplication from step 1 to the rest buttons.
1. Press & hold button 1 of the duplicator, meanwhile press 4 times the 2 button.
2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.
3. Place the original remote control next to duplicator around 5cm
4. Keep pressing the button of the original remote control and wait for a change flash (as a faster flash) of duplicator RED LED and a change of its color (BLUE) that confirms the correct learning of code. This step may take a few seconds and during that the color LED is WHITE.
5. While the BLUE LED is flashing, press the button of the “duplicator” where you want to program the code just learnt, and retain pressed until the LED will switch off. The duplicator remote control will emit an extended sound “BEEP” for are confirmation of the correct code learning.
6. Repeat the duplication from step 1 to the rest buttons.
7. Activate now the correct procedure for the programmed model and insert the new remote control on the receiver (seethe compatibility list present in this manual).
|
3.1 BFT
1. Press & hold button 1 of the duplicator,meanwhile press 4 times the 2 button.
2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.
3. Place the original remote control next to duplicator around 5cm
4. Keep pressing the button to be programmed of the original remote control, till the RED LED will switch on as a fix light; now release the button.
5. The duplicator RED LED will emit a
short flash every 2 seconds supported by two following sound “BEEP”. These two alerts
indicates it is necessary to
emit the SEED CODE to realize
the copy.
6. To transmit the SEED CODE of the BFT original remote control, please using a
pin, press the rear hide button (see the picture)or, according to the new references, press the 1 and
2 buttons until the original remote control LED switches on.
7. Now the duplicator RED LED will change the flash mode (more fast) and color (BLUE), for a reconfirmation of the correct code learning. This step may take some seconds.
8. At this moment, press the duplicator button when you want to store the code and retain pressed until the duplicator BLUE LED switches off and an extended sound “BEEP” is emitted for a reconfirmation of the correct code learning. Repeat the duplicationg from Step 1 to the rest buttons.
9. Activate now the DOR procedure to insert the new remote control on the receiver.
1. Press & hold button 1 of the duplicator,meanwhile press 4 times the 2 button.
2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.
3. Place the original remote control next to duplicator around 5cm
4. Keep pressing the button to be programmed of the original remote control, till the RED LED will switch on as a fix light; now release the button.
5. The duplicator RED LED will emit a short flash every 2 seconds supported by two following sound “BEEP”. These two alerts indicates it is necessary to emit the SEED CODE to realize the copy.
6. To transmit the SEED CODE of the V2 original remote control, please press at the same time 1 and 2 buttons.
7. Now the duplicator RED LED will change the flash mode (more fast) and color (BLUE), for a reconfirmation of the correct code learning. This step may take some seconds.
8. At this moment, press the duplicator button when you want to store the code and retain pressed until the duplicator BLUE LED switches off and an extended sound “BEEP” is emitted for a reconfirmation of the correct code learning. Repeat the duplicationg from Step 1 to the rest buttons.
9. Activate now DOR the procedure to insert the new remote control on the receiver.
Attention: verify the programming remote control is a MASTER. Pressing whatever button, the LED has to emit a double flash rather than to switch on as a fixed light.
1.