LeLuv Eyro Stainless Steel Glans/Cock Rings 5mm Width | Choose Diameter & Height

KEY FEATURES:

• Eyro 5mm Stainless Steel Penis Rings - Choose Height from 5mm through 25mm & Diameter from 22mm to 32mm
• Penis Rings are designed to help prolong your erection, and add some flair at the same time! The Penis Ring is intended to rest behind the male genitalia, flat against the body
• To wear the Penis Ring, feed each testicle through the hole first, followed by the flaccid shaft. The rounded edges help ensure comfort, even when wearing on a semi-permanent basis.
• Glans Rings are designed to fit under the corona (head) of the Penis and provide enhancement and size to the head only
• Crafted in solid "304" Stainless Steel then polished smooth and shiny, the heavy feel adds unique sensations that other materials can't match. Extremely safe, won't rust and is easy to clean

More Sizes! Better Fit! LeLuv® EYRO Penis and Glans Rings are designed in more sizes for a better fit. The right fit is important... 1-2 mm can matter. Our Sampler Set provides a range of three Ring sizes across 4mm (.16") and saves you over 12%! Five Ring heights are offered in all diameters; 5mm, 10mm, 15 mm, 20mm and 25mm.

Crafted from 100% 304 Stainless Steel and hand polished. Precisely machined 304 Stainless Steel is extremely safe, won't rust, and is easy to clean. Rings from 22mm (0.87") to 34mm (1.34") can be used as a glans ring around the head of the Penis. Penis rings are intended to rest behind the male genitalia, flat against the body and can help prolong your erection and add some flair at the same time!

To wear the Penis ring, feed each testicle through the hole first, followed by the flaccid shaft. The rounded edges help ensure comfort, even when wearing on a semi-permanent basis.
It's essential to use and size these devices safely and as instructed to enjoy the potential benefits without any risks. LeLuv® EYRO constriction rings have a standard width of 5mm and have multiple inside diameter sizes to choose from ranging from 22mm to 66mm. To find the correct size, stainless steel constriction rings should be sized about 5mm to 6mm smaller than the male genitalia in an unaroused or flacid state. It's important to remember that 'sizing' a constriction ring when aroused could lead to discomfort and potential injury. A properly sized ring should fit behind both testicles, up against the base of the penis without being too tight or too loose to experience maxium results. Constriction Rings can also be placed just under the head or glans of the penis to restrict flow from leaving while increasing size and sensitivity.

How to Size a Cock Ring: A Step-by-Step Guide

To ensure a snug fit that won’t slip off, the inside diameter (ID) of your cock ring should be smaller than the diameter of your penis. A general rule of thumb is to choose a ring with an ID that is 6 mm smaller than your penis diameter. Since measuring the penis diameter directly can be challenging, measuring the penis circumference is the recommended method. Use this measurement to find the closest match on our chart, ensuring a comfortable and secure fit.

Here’s how you can determine the right size:

1. Measure Your Penis Circumference:

   • Use a measuring tape or string to measure the circumference of the area where you want to place the ring (e.g., the glans, middle of the shaft, or base of the penis).

2. Determine the Corresponding Ring ID:

   • Take the measured circumference and use it to find the corresponding ring ID from our sizing chart.

3. Apply the Rule of Thumb:

   • For a snug fit, your penis diameter should be approximately 6 mm larger than the ring's inside diameter. For example, if your penis diameter is 28 mm, you should choose a ring with a 22 mm inside diameter.

Eyro Glans/Penis Ring Conversion Chart

---

---

---

---

---

---

---

---

---

---

---

---

---